The cost lines in a laser cutting price
| Line | How it is calculated |
|---|---|
| Material | Sheet area used by the part × thickness × material density × price per kilo, plus a scrap allowance |
| Cutting time | Total cut length ÷ cutting speed |
| Piercing time | Number of pierces × time per pierce |
| Machine cost | (Cutting + piercing + set-up time) × machine hourly rate |
| Finishing | Per-part or per-job charges for bending, deburring, welding, painting |
| Margin and tax | Profit margin and VAT |
The laser cutting price formula
Unit price = Material cost + (Cutting time + Piercing time) × Rate per minute + Finishing
Quote price = Unit price × Quantity × (1 + margin) + fixed per-job charges
The rate per minute is the machine’s hourly rate divided by 60. The hourly rate covers depreciation, power and gas, maintenance and the operator, which is why it differs from one shop to the next.
A worked example
The figures below only show how the calculation works; they are not market prices. Use your own hourly rate, cutting speeds and material prices.
- Part: 150 × 120 mm bracket, 5 mm mild steel, total cut length 701.7 mm, 4 holes
- Net area 66.2 cm² → weight: 66.2 cm² × 0.5 cm × 7.85 g/cm³ ≈ 0.26 kg
- Example material price £1.20/kg, 20% scrap allowance → material ≈ 0.26 × 1.20 × 1.2 ≈ £0.37
- Example cutting speed 2,400 mm/min → cutting time ≈ 701.7 ÷ 2,400 ≈ 0.29 min
- Example pierce time 0.03 min → 4 holes ≈ 0.12 min
- Example hourly rate £90 → £1.50 per minute → machine cost ≈ (0.29 + 0.12) × 1.50 ≈ £0.62
- Deburring, example £0.50 per part
Unit cost ≈ £0.37 + £0.62 + £0.50 = £1.49. Margin and any fixed per-job charges (set-up, packing, delivery) are added on top, and VAT on the invoice.
To run the same sum with your own figures, use our laser cutting cost calculator; it shows every step.
What decides the cutting speed?
Cutting speed depends on the material (mild steel, stainless, aluminium), its thickness, the laser’s power, the assist gas (oxygen, nitrogen or air) and the edge quality required. As thickness goes up, speed falls and pierce time rises, so the same part gets disproportionately dearer in thicker material. For accurate prices you need a table of your own machine’s real cutting speeds.
Why do two shops quote different prices?
Hourly rates, machine power and gas costs differ. A shop with good nesting on the sheet wastes less material. Some add a minimum order charge or set-up time. Finishing work (bending, deburring, painting) is priced separately. That is why comparing price per metre alone is misleading.
Pricing automatically from the drawing
Cut length, pierce count and part area can all be measured from a DXF drawing. Software can take those measurements, apply your own hourly rate, cutting speeds and material prices, and hold the quote for your approval before it goes to the customer. We built this into Dipro Teklif, our quoting software for fabrication workshops.
Frequently asked questions
Why isn’t laser cutting simply priced per metre?
A price per metre only accounts for cut length. Pierce count, material weight, cutting speed that changes with thickness, and finishing all affect the price as well, so an accurate price is worked out part by part.
How does thickness affect the price of laser cutting?
As thickness goes up, the part gets heavier, the cutting speed falls and piercing takes longer. Together these push the price up faster than thickness alone would suggest.
Can you get a laser cutting price without a DXF drawing?
For simple parts, a dimensioned sketch is enough for an estimate. A firm price needs a DXF or similar drawing so the cut length and pierce count can be measured.
This guide was prepared by the dipro.uk team and last updated on 16 November 2026. Questions: [email protected].
